115V-220V Black Server Cabinet Assembly (less side panels)
(1) 772444 Patented Aluminum Extruded Welded frame with (4) additional stiffeners for additional strength, (2) top and (2) bottom, aluminum corner castings, Floor Style 12 GA CRS Base, vented front and rear with welded and cleaned corners.
O.D. 84.58"h x 28.33"w x 47.545"d
I.D. 77.09"h x 24.09"w x 44"d
(1) PFT2444-2535 -- Pagoda Fan Top panel with (2) 115V, 535 CFM fans, each have their own cord and plug, all corners are welded and cleaned, top panel is externally removable and is installed using closed cell foam to create a tight seal. 16 ga. CRS
(1) GD7724X -- Glass door with lockable swing handle, key # EK328, RIGHT HAND HINGE. Scuff plate for latch,12 ga.Trim strip with studs to hold glass clamp strips, 3M 2 WAY tape on both sides of glass, extra clamp strips for added strength, aluminum extruded welded frame with ¼" CLEAR tempered glass and aluminum corner castings
(1) SD7724 -- Solid Rear Door with lockable swing handle latch, key # EK328, RIGHT HAND Hinge, (1) Hat Section & document holder,16 GA.CRS
(2) VSB77 -- Vertical Support Bar with (6) holes to mount to stiffeners and Xties, one each located each side of the enclosure at rear
(16) FCM2X5D-2 -- Fiber Cable Management bracket with door on 2" side and radius bends on top and bottom for Fiber Cabling and (2) pcs. of Velcro, one on each radius. Mount to VSB77 equally spaced top to bottom, (8) per side. Made of 14 ga. CRS
(2) PSBL60-20-6-TL 115V Vertical Power Strip, 20A, (20) 5-20R Receptacles, 6ft cord with L5-20P TWISTLOCK PLUG ASSEMBLE BOTH AT RH REAR, FACING FRONT
(2) PSM7024-220-AF1 220V Vertical Power Strip, 30A -mounts in 40-44u cabinet -(24) IEC320 C13 receptacles wired in (3) banks of (8) each -(6) 10A Circuit Breakers, (2) per bank -6ft cord with L6-30 plug
ASSEMBLE BOTH AT LH REAR, FACING FRONT
(1) TH100 -- Thermostat to control one fan, comes with mounting bracket and Lexan cover
(1) ADJ RAILKIT 7720-Adjustable Rail Kit with (4) "L" Shaped Vertical Mounting Rails with each "U" Marked with Small Hole Set 3" back from Front & 29.000" apart. Top and Bottom Welded Flanges.Front flange of all rails to be 1.165"
(4) "Z" Shaped Stiffening Brackets Approx. 50"Long that support the "L" Shaped Rail. (28) 10-32 Pemnuts installed in "Z" Bracket (28) 10-32 Flathead Screws (28) 1/4-20 Spring Nuts(16 w/SHORT SPRING) (16) 1/4-20 x 3/4" Screws (12) 1/4-20 x 1/2" Screws (24) 10-32 Spring Nuts in a plastic bag attached to rail-Used to secure vertical mounting rail to frame when 24"mounting is desired.
(3) HSB24-2--Horizontal Support Bar (double) made of 6061-T aluminum extrusion
(2) HSB04-2--Horizontal Support Bar (double) made of 6061-T aluminum extrusion
(1) VSR14-5R -- Pair of 5" Reducer Rails w/4 cable cutouts each, square mounting holes for M-6 Cagenuts, mounts to bottom crosstie and lower Stiffener. Mount just behind rear set of 77" rails
(1) M6-40 Hardware Pack
(1) CPL4248 - 42" x 48" Cushioned Pallet, bolt down brackets, bracket hardware and Luan on sides